Nice article on Meshtastic. The problem is that, like anything, the actual distance is a lot more dependent on line of sight and the actual mesh existing. Which means we’d need a LOT more people to adopt these and put up repeaters for them to be useful. Which is doable, but not cheap.
I always thought these were more like walkie talkies for messaging than telephones that you can call anyone.
Like it would be good if cell serivce goes down.
Why not just add networking capabilities or a SIM card?
Clickbait title. Just say it’s meshtastic.
Ok…what’s meshtastic? I still haven’t clicked the article, and know nothing of which you speak.
I’d say this title is for people like me. I think it sounds cool.
It is cool! The barrier to entry is relatively low. The only thing to really worry about is:
- What band/frequency is appropriate for you country.
- Are there others around to which you can connect?
If there’s not a lot of people around it’s not the end of the world. Nodes can connect over the Internet via MQTT servers. Yes, this defeats the purpose of having an offline/decentralized communication platform, but it is a good stop gap until more nodes are put up.
Here’s a sample of what I can see in a somewhat large-ish Midwest City in the US (there’s about 63 nodes I can reach by hopping through relays).
I got mine recently in a dxent aized city and while there are plenty of nodes popping up on the map, the local channel is pretty quiet. Is that normal?
Yep, that can be normal. For my city, the local group has a private (but free to join) channel that’s a bit more active.
Do a web search for meshtastic and your city and see if one pops up.
I don’t know. It’s the same for me but I got a pretty bad reception. The only time I saw some messages was when someone was sending some from a plane, so I guess it was a special occasion.
Where’d you get that map from?
The official meshtastic app has a map view that shows all known nodes.
It allows us to make a mesh network (interconnected nodes where you can contact a node even if it’s not in range for you, by using other nodes) with Lora radio devices. Lora is slow but has long range. I think it works better when you have line of sight, like if someone can put a node on a mountain, it would help everyone.
I think people might have sent audio with it but it’s mostly useful for text messages. It could be useful if the Internet is down, maybe, but it’s more like a toy.
It could be useful if the Internet is down, maybe, but it’s more like a toy.
Since LoRa devices use very little power this can be useful when there is no electricity.
I mean it’s an article for people like me who have never heard of that
Sure, but they could at least put that in the title as well so people who are familiar w/ it don’t need to click through.
I maintain three of these devices, if anyone has any questions.
What is the range of a device like this? Is there any chance of using a mesh system like that if you’re not in a city? I’m about 30 miles away from a few towns, so there’s little chance for repeaters to be nearby.
Theoretically you can get 50 ish miles or more with line of sight. In practice, you can get around 10 ish with repeaters. With around 30 devices, our city has effective coverage.
You also have options to use MQTT if you want to make sure a message gets through. But that requires an internet connection.
What about without line of sight? If I get one of these is it going to work while it’s sitting on my desk, or am I going to have to mount some antennas on the roof to actually make it usable? The maps only show like three other people in my city with one, so I’m not sure how useful this will actually be for me.
Honestly, its a fun side project, but without enough nodes its more of a hobby. If you want to make it usable, its probably better to use internet or higher power devices (like ham). Or buy a metric ton of these and throw them up high.
As long as you have a node in sight, it should be good for at least some communication. My little window node gets 20+ nodes.
Additionally is there a way to search what’s already out there without a device?
You can, there are websites that show some of the devices. But from what I’ve found, it’s only showing around 1/4 of the real devices in the area. Or at least where I am at.
I’m on the phone so I’m not sure off the top of my head, but I think someone already linked a couple above.
Thanks. I eventually saw that comment and I am just a bit out of range of one listed.
How does this differ from IP over ham radio? It seems like in general, it would just be lower distance and greater reliance on nodes near you, with the trade off being smaller equipment.
https://themodernham.com/ip-over-ham-radio-via-new-packet-radio/
Its biggest + in my book is that you don’t have to be a ham to make it work. There are better systems if you want more reliable communications. But its a fun side hobby and, in the event of a power outage, a decent little communicator. Although from personal experience, most of the devices piggy back of your existing cell phones and bluetooth. So ironically as long as the cell towers aren’t blown to hell, your still fine either way.
You don’t need cell towers. Your phone is just used as an input device for the radio.
There may be some miscommunication. I ment that in order to use a majority of the meshtastic devices, they require the android or ios app + bluetooth. Not all, but a vast majority. And most of those will have access to a cell phone tower that will likely not go down, even in the event your neighborhood power goes off. At least where I am at. The devices have often been alluded to a disaster proof communications device. And an alternative to instant messaging. Its not as reliable as some other tech that is out there, but its a fun hobby!
Hope that makes more sense.
Gotcha. I read your post wrong.
The phones are one reason I don’t think Meshtastic is good for emergency communications. My main Meshtastic devices run off a battery pack that can run them for 2-3 weeks, but I’d also have to keep a phone charged throughout the disaster to use them.
What is the typical power requirement on these devices? Can it be used to set up IoT sensor nodes in the wild where they work off solar, or do they need periodic tuning/care?
I’m running about 1w per device ATM.
So yeah it sips energy. There’s a lot of nodes in the mountains that are solar powered. They work.
That’s a great idea. The area I live in is pretty mountainous so putting nodes on ridges provide pretty good coverage
Very low and yes. They work great for IoT, as long as it’s not mission critical stuff as messages can get dropped or arrive out of order sometimes. But for something like monitoring a remote sensor station that’s within the Lora range, without needing a cellular plan, yes.
I got mine recently in a dxent aized city and while there are plenty of nodes popping up on the map, the local channel is pretty quiet. Is that normal?
Yeah, we had to make a weather app on longfast to fill the void. Tech people tend to not talk all that much. We are the strange ones ;)
Most of the weather app was made from a reddit post back a year or so ago. I have no idea where though. App is a python script here if your interested.
What kind of data rate can they provide? Can it support audio? Low bit-rate video?
I’ve seen LoRa when Pine64 announced some related products some years back, but I haven’t really gotten into it. If the community is big enough and the bitrate reasonable enough, I might get one to connect my home to my parents home (about 10 miles away, so at the edge of the range) for fun. It would be cool to set up some smart home stuff at both ends that I could host on my own so I can keep an “eye” on my parents stuff when the travel (mostly just door and occupancy sensors, no video).
In theory the protocol can support those formats. With meshtastic it’s only designed for text. You can get some really basic emojis though since they are Unicode.
If its simple enough, I could probably abuse it to send binary data by encoding everything in base64 or something, and writing a simple translator for whatever my app is.
But what does the usable bandwidth look like, and what about latency? If I’m going just out of range from direct communication, I assume I’d be going through other peoples’ nodes, but is that intelligent enough to route messages through efficiently? Or could I see crazy latency spikes?
You are at the edge of what I know :) If you find out, let the rest of us know. I only have vague and hand wavy knowledge at this point of lora slow means lots of latency. GL!
The maps do not show any devices in the country where I live, but due to the low cost and practical use, I’d love to set some up.
If i am usually within 6km of my home, in a city. I wonder if 1 node will be enough coverage.
Also, how can you tell that there are more nodes than reported on those sites?
The phone app gives the location of nodes want you to know. And most don’t care. For example, in my city there is currently 24 online nodes my window node has interacted with. And 174 in total nodes it’s contacted today.
It can be spotty during certain times of the day.
My wife and I each have a radio, as do several of my friends. They’re handy for anything where you may not have cell coverage, like camping. We also use them at protests, to avoid the heavy surveillance that’s being done on cell networks. Even if the authorities start looking at Meshtastic, everything except the public channel uses PGP end-to-end encryption, and there is no middleman that has access to the unencrypted data.
We have also put up a repeater node. It’s on top of a house at the top of the highest ridge near us. Before it went up we rarely saw more than our own nodes. Now we see several dozen, and sometimes a lot more. And the repeater serves the whole community, not just us. The beauty of a mesh is that everyone contributes to everyone else’s coverage.
The mesh in our city is growing rapidly right now. Not only are there a lot of people getting their own nodes, there are a surprising number of people putting up repeaters to help spread the coverage. It’s amazing to watch our whole neighborhoods suddenly appear as gaps are filled in.
How do I do this? Shats the easiest way to get started?
Both a personal device and a repeater on my house
Easiest and least expensive are a little different, so I’ll talk briefly about both.
The easiest is to go on Etsy and search for Meshtastic. You will find plenty of people who will build you a ready-to-go unit, both individual radios and solar-powered repeaters. (If you plan to put your repeater somewhere with power you can use any radio as a repeater, just put a good antenna on it.) Pre-built units start at around $60 and can go up into the hundreds, but $60 to $90 will get you a great personal radio.
The least expensive is to order a kit from one of the many companies that sell them. If the kit does not come with a case, check Etsy for cases that match your kit. Most kits do not require soldering, you just have to plug in various cables and connectors, then fit everything into the case. Some actually come fully assembled. This approach generally costs somewhere between half and two-thirds of what a pre-built setup will run. Kits start as low as $10, although most or $20 to $40, and cases are mostly $20 to $35.
One of the harder parts is to figure out which radio kit you want, but there are just two major types. Those built around the ESP32 processor tend to be a little less expensive and offer the option of WiFi, but they have a much shorter battery life. Those built around the nRF52 processor cost a little more, do not offer WiFi, but have nearly 10 times the battery life. WiFi is only used in a few specific cases, usually by repeaters and not personal units, so you may well not need it. Battery life is not usually an issue for personal radios, since nearly all of them will go for a full day between charges, but sometimes you may want more than that. Stand-alone repeaters that run off solar panels are almost all based on the nRF52 because of the battery life.
The most common starter radios are based on the Heltec V3 kit, which is based on the ESP32. It has been around a long time, it is relatively inexpensive, and it can do pretty much everything. The only downside is battery life, which may or may not matter to you. Unless that’s a concern, you can’t go wrong with a V3. My personal favorite is the T114 kit, also from Heltec, which is based on the nRF52. It is much like the V3, but without WiFi and with much better battery life.
I would wait until you’ve played with a personal radio before buying a repeater. Every Meshtastic radio acts as a repeater, so you don’t necessarily need a dedicated repeated. Find out how many nodes are in your area and what kind of coverage you get. If there aren’t many nodes, or distance is limited, you can consider a dedicated repeater.
Basically, a repeater is just a node with a good location that’s put in a good location, up as high as possible. Because Meshtastic radios use very little power, it is practical to make completely self-sufficient solar repeater units that never require charging. You can put one of those on your roof, up in a tree, or on top of a nearby hill or mountain, without having to worry about regularly climbing back up there.
I strongly recommend that you go to meshtastic.org and read through the Getting Started documentation. It provides a lot more detail (and less personal opinion). And check out the Meshtastic communities on Lemmy. Have fun!
Save worthy post. Not the person who asked, but thanks for the extremely detailed response!
I’m glad it was useful to you!
Thank you for the detailed reply! Yeah I realize now Mestastic.Org has everything I need.
Planning to prolly get:
A rak wireless kit for a local repeater on my roof powered via PoE, and then a TTGO TEcho for my personal device.
I know that I should just get the latter and play with it first, but I live high on a hill with a great vantage point of the city so feels like a disservice to the community if I don’t also host a repeater.
One thing I’m curious about, is if I use it via poe, can I also send messages via the repeater? I.e. locally from my network initiate a message through my repeater?
I would want it in repeater mode so it would forward any message even ones I don’t have the encryption key for.
I don’t think any of the current Meshtastic radios can be used in the usual way via ethernet. Some support WiFi, but not the RAKs that I know about. That leaves USB and Bluetooth.
There is a very neat option that allows you to set up to remotely administer a node via radio. That has saved me a lot of trouble with my repeater. You can’t do everything that way that you could with a direct connection, but you can do most of it.
The repeater will automatically forward messages from your personal radio to anyone who is outside your direct range. You don’t have to do anything special to make that happen. Likewise, any node, including your repeater and your personal radio, will automatically forward encrypted messages without knowing what’s in them. Only the endpoints need to have the encryption keys. Anything in between just forwards the raw data.
Man I’ve been seeing so much about these over the last few weeks, I’d love to get my hands on one
I just picked up a 2pack of devices from the Amazon link in that article. Planning on messing with them this weekend. I figure I’ve spent more than $60 on random projects that went nowhere before, so this can’t be that bad.
LoRa has been around for a while trying to break through with different devices, some of it does seem useful, but it’s a tough sell to invest in something without knowing where the network will go. A carrier model or something else, maybe subsidies, is needed.
Not much bandwidth to know do much beyond text, so use-cases are probably very limited already.
I sent this link to a friend who’s really into internet radio (like CB used to be cool for nerds) who also loves to 3d print. He lives in a plains state, where this should work really well.
